What Is The Best Gauge Wire For Speakers?

What happens if wire gauge is too big?

using larger wire will not hurt anything or cause any overload.

The larger wire will cost more, the pathway or where it has to fit, and the physical size of the connecting means (ie.

the size of terminal or clamp it has to fit in), will all be determining factors in just how big is too big..

Can I use different gauge speaker wire?

As long as you have the same diameter wire, per pair of matched speakers, you will be fine. An instance where you would not want to use them is a different guage for a left and right speaker. Depending on you amplifier, this could cause a problem if you place a large load on the amp for an extended period of time.

Does speaker wire brand matter?

Registered. So as an electrical engineer, I will tell you that as long as the actual conductor material was made of pure material (i.e. copper, etc), then it doesn’t matter about the brand.

What gauge speaker wire should I use for subwoofer?

The speaker wires If your sub system is going to put out more than 1,000 watts RMS, you can use 12-gauge speaker wire. But 16-gauge speaker wire works well for most installations.

What is the smallest gauge speaker wire?

22 AWGWire Gauge Speaker wire typically is available in even increments between 22 AWG and 10 AWG; where 22 AWG is the smallest and 10 AWG is the biggest. With thicker wires, the resistance of the cable is reduced, allowing you to run cable in longer lengths than you would be able to with thinner wire.

What is bigger 12 AWG or 14 AWG?

The diameter of solid 12 AWG wire is approximately 0.0808 inches (2.053 mm), and 14 AWG is 0.0641 inches (1.628 mm). Therefore, 12 AWG wire is about 26% thicker and has 59% more cross-sectional area than 14 AWG wire.

How many watts can a 12 gauge wire handle?

building wire14 – Wire12 – WireRecommended 80% Wattage Load: 1440 watts (120 volts). Max Wattage Load: 1800 watts (120 volts).Recommended 80% Wattage Load: 1920 watts (120 volts), 3840 watts (240 volts). Max Wattage Load: 2400 watts (120 volts), 4800 watts (240 volts).Recommended ForRecommended For4 more rows

Does speaker wire gauge affect sound quality?

Generally speaking, resistance starts to have an effect on the performance of a speaker when resistance is greater than 5% of the speaker’s impedance. … The thicker a wire or the lower the gauge, the less resistance. It is therefore a combination between speaker impedance, length and gauge that affects the resistance.

Is 18 gauge wire OK for speakers?

All speakers work best with the largest gauge wire possible, 18 being the “standard”. … The manual states that up to 20 ft an 18 gauge wire is fine with 16 and 14 gauge for longer runs.

Which is bigger 14 AWG or 16 AWG?

The size of the wire in diameter. 14awg is larger in size than 16awg. There is a distance that you can run 14 vs 16awg and not lose performance based on ohm load.

Is it OK to oversize wire?

Yes, you can oversize a wire. You can use #12 on a 15a circuit or #10 on a 20a circuit. … If you feel safer with # 12 on a bedroom circuit, then you might as put it on a 20a breaker. You will have more ampacity, more efficient.

What happens if you use the wrong gauge wire?

What can happen when you use too small of wire size for your equipment? … If too small of a size is used, the wire could melt because of the large amount of current flowing through it compared to how much the cables can handle. The smaller the wire diameter, the higher the resistance there will be to the flow of energy.

Is 12 AWG speaker wire overkill?

Thick wire (12 or 14 gauge) is recommended for long wire runs, high power applications, and low-impedance speakers (4 or 6 ohms). For relatively short runs (less than 50 feet) to 8 ohm speakers, 16 gauge wire will usually do just fine.

How far can you run 14 gauge speaker wire?

The rule is the total resistance of the wire should be less than 5 percent of the rated impedance of the speaker. Your Insignias are 8-ohm speakers, which means 16 gauge is good for up to a 48-foot run (per speaker). Speaker wire of 14 gauge is good for an 80-foot run, and 12 gauge is good for 120 feet.

How many watts can 14 gauge speaker handle?

750 watts14 AWG Speaker Wire can handle up to 750 watts of power at 20 ft Cable Runs: 14 guage speaker wire can carry up to 750 watts of power with 20 ft of speaker wire and a 4 ohm speaker load with 37 watts lost at the speaker terminals.

Do banana plugs affect sound quality?

Why Banana Plugs. There are many benefits of using banana plugs with your speaker wire. Not only do they help your installation to look cleaner, banana plugs also give you a permanent and high quality connection. … Wires tend to get pulled out or frizzy as time passes, which can affect your sound quality.

Are expensive speaker wires worth it?

An expensive cable might sound worse on your system than cheap cable. Or it might sound better. The important thing to remember is that even if it does sound better, it’s such a minuscule improvement that pretty much anything else you can do will have a greater effect on the sound.

Is 14 gauge speaker wire good for subs?

As mentioned already, subwoofers typically use lower gauge wire. The most common speaker wire gauges for subwoofers are 16, 14, and 12. … When choosing a gauge, it is better to round up than to round down in size. Using an 18 gauge wire when you need a 14 gauge wire will result in poor performance from your subwoofer.

Is higher gauge speaker wire better?

A lower-gauge number indicates a thicker wire, while a higher-gauge number indicates a thinner wire. Speaker wires with lower-gauge numbers are better at carrying an amplified audio signal. … However, for longer speaker wire runs (to another room, for example), it is better to use a thicker, lower-gauge wire.

How many watts can 16 gauge speaker wire handle?

As with the power wire, the longer the run and the more current you’re pushing through it, the larger size you should use. For example, if your amp is in the trunk and you’re sending 100 watts to your front speakers, 14-gauge speaker wire is a good call. But if the amp is only 50 watts, 16-gauge would be fine.

Can I use higher gauge wire?

You can always use a larger gauge than is required So if you have a 15A circuit, you are required to use least 14 AWG wire. However if you want to use #12, #8, 4/0… whatever, as long as your wiring methods are proper.